Furnace Replacement Cost - Real Local Prices, Then Your Exact Quote

How Much Does Furnace Replacement Cost in Yonkers?

A full furnace replacement in Yonkers typically runs between $3,800 and $7,400 for most single-family homes, with the average homeowners in neighborhoods like Park Hill, Dunwoodie, and Crestwood spending between $4,500 and $6,200. High-efficiency units (90%+ AFUE) push the upper end of that range, while straightforward mid-efficiency swaps on homes with existing ductwork land closer to $4,000. The final number you pay depends on the furnace brand, your home’s square footage, whether you need venting upgrades, and the contractor you choose.

Here’s what actually matters: Yonkers homes range from compact pre-war bungalows in Lincoln Park to sprawling Colonials in the hills along Central Park Avenue, and furnace sizing follows that spread. A 60,000 BTU furnace that heats a 1,200-square-foot ranch in southeast Yonkers costs considerably less to install than a 100,000+ BTU unit for a 3,000-square-foot home near Dunwoodie Golf Course. We’re going to break down every line item so you know exactly what you’re paying for before you call anyone.

Andre Fuller, owner at Halden Heating and Air Yonkers, puts it plainly: “Homeowners in Yonkers shouldn’t have to guess what a furnace costs. We give a written price before any work starts, and that’s the price. No surprises at the door.”

Call (838) 213-7827 for a free furnace replacement estimate in Yonkers. Written price, no obligation.

Furnace Replacement Cost Breakdown (2026)

Furnace replacement pricing in Yonkers breaks down into equipment, labor, and ancillary work. Here’s a realistic line-by-line look at what you’ll see on a quote from any reputable Westchester County HVAC contractor in 2026:

Line Item	Yonkers Price Range (2026)	Notes
Furnace unit (mid-efficiency, 80% AFUE)	$1,400 – $2,800	Goodman, Rheem, Bryant, and Carrier base models all fall here.
Furnace unit (high-efficiency, 90-97% AFUE)	$2,500 – $4,800	Two-stage and modulating units from Trane, Lennox, and Carrier sit at the top.
Installation labor	$1,200 – $2,500	Usually 1-2 days for a crew of two; includes removal of the old unit.
Permits and inspection	$150 – $450	Yonkers requires a mechanical permit for furnace replacement; most contractors roll this into the quote.
Sheet metal / plenum work	$200 – $800	New furnaces don’t always match existing duct connections; some fabrication is almost always needed.
Venting upgrades	$0 – $1,200	High-efficiency units vent through PVC side-wall piping instead of a chimney; retrofitting a chimney-vented basement furnace adds cost.
Smart thermostat (optional)	$150 – $400	Often bundled at a discount during replacement.
Old furnace removal and disposal	$100 – $300	Usually included, but some contractors line-item it.

Realistic total for a typical Yonkers single-family home: $3,800 – $7,400.

What pushes you toward the high end? A big house in Crestwood or Colonial Heights that needs a 120,000 BTU high-efficiency Trane, plus a venting conversion and a new smart thermostat. On the flip side, a 1,000-square-foot ranch in southeast Yonkers getting a direct-swap 80% Goodman with an existing chimney vent will land around $3,800 to $4,500. Andre Fuller has seen hundreds of Yonkers quotes over the years, and that spread holds up.

Here’s the thing about HVAC pricing in Yonkers specifically: you’re paying Westchester labor rates, which run about 15-25% higher than upstate New York and 10-15% lower than Manhattan. The city’s mix of aging housing stock means about 40% of the furnaces we see being replaced are 25+ years old, which often means additional duct adapter work. That’s normal. A good contractor accounts for it in the written quote rather than surprising you mid-job.

What Affects Furnace Replacement Pricing in Yonkers

No two furnace replacement quotes in Yonkers look identical, and these are the factors driving the differences:

• Home size and BTU requirements. Furnace output is measured in BTUs (British Thermal Units), which is the amount of heat the unit produces per hour. A 1,000-square-foot home north of McLean Avenue might need a 45,000-60,000 BTU furnace, while a 2,800-square-foot Colonial near Tibbetts Brook Park needs 90,000-110,000 BTUs. Bigger furnaces cost more, period.
• Efficiency rating (AFUE). AFUE stands for Annual Fuel Utilization Efficiency, which is the percentage of fuel that actually becomes heat for your home. An 80% AFUE furnace wastes 20 cents of every dollar of gas; a 96% AFUE unit wastes only 4 cents. High-efficiency units cost $1,000 to $2,500 more upfront, but Yonkers homeowners with Con Edison gas bills of $250+/month in winter often recoup that in 5-8 years.
• Venting configuration. This is the sleeper cost factor in Yonkers. Most pre-1990 homes here have chimney-vented furnaces. High-efficiency furnaces don’t use the chimney, they vent through a side wall using PVC pipe (condensing furnaces produce cool exhaust). If your basement furnace sits far from an exterior wall, running that PVC gets more expensive. Some Yonkers homes need $800-$1,200 in venting work alone.
• Ductwork condition and compatibility. Newer furnaces have different physical dimensions than the units they replace. Often, the metal transition box (plenum) that connects the furnace to your ductwork needs custom fabrication. If your ducts are undersized or leaky, that’s a separate conversation, but it can add $500-$2,000 to the project scope if it’s affecting heating performance.
• Furnace brand and tier. You’re paying for build quality, warranty length, and parts availability. Goodman and Rheem are solid budget-to-mid options with 10-year parts warranties. Carrier, Trane, and Lennox sit in the premium tier with better sound insulation, tighter build tolerances, and 10-12 year warranties. A comparable 96% AFUE furnace runs about $500-$1,200 more from Trane than from Goodman. Whether that’s worth it depends on how long you plan to stay in the house.
• Seasonal timing. The busiest season for furnace work in Yonkers runs from late October through February. Replacements scheduled during summer or early fall sometimes price out 5-10% lower simply because demand drops. That said, a failed furnace in January can’t wait, and Halden Heating and Air answers calls live 24/7 with same-day and next-day replacement availability through the heating season.

One more Yonkers-specific note: the age of your home matters. We work in a lot of 1920s-1960s houses where the existing furnace sits in a cramped basement alcove behind a staircase or under a low ceiling. Getting the old unit out and the new one in can require disassembly or creative rigging. A competent crew handles it. But it’s labor time, and labor time is money. Ask your contractor to walk the access path before quoting so the written price reflects reality.

Furnace Replacement vs. Furnace Repair: Which One Do You Need?

Not every furnace problem requires replacement. Here’s how to think about it in Yonkers terms.

Furnace repairs in Yonkers run between $150 and $700 depending on the part and the problem. Common fixes include:

• Ignitor replacement: $150-$350
• Flame sensor cleaning or replacement: $100-$250
• Blower motor capacitor: $150-$300
• Gas valve replacement: $300-$700
• Control board replacement: $400-$700
• Inducer motor replacement: $450-$700

The math gets simple when you apply the “age times repair cost” rule: if your furnace is over 15 years old and the repair estimate multiplied by the unit’s age exceeds $5,000, replacement almost always wins. Example: a 20-year-old furnace needs a $650 control board. That’s 20 × $650 = $13,000 worth of expected future spending on a unit already past its life expectancy. Put that $650 toward a new furnace instead.

Other replacement signals: cracked heat exchanger (a safety issue, see below), frequent cycling (turning on and off too quickly, usually a sizing or airflow issue), rising gas bills with no change in usage, and loud rumbling or banging sounds from the cabinet.

If you’re unsure, call (838) 213-7827 and Andre Fuller or a Halden technician will give you an honest read. We’d rather tell you a repair is all you need than sell a replacement you don’t. Every repair we do carries a written guarantee, and if it fails within the coverage window, the second visit is free. That’s standard, not an upgrade.

Signs Your Yonkers Furnace Needs Replacement

Here’s what homeowners in Yonkers should watch for as their furnace ages. Several of these overlap with repair needs, so don’t panic, but a combination of three or more signals on a 15+ year old unit means replacement is on the horizon.

Your furnace is 15-20+ years old

The average furnace lifespan in the Northeast is 15-20 years, and Yonkers heating systems that run from October through April get worked hard. If your unit was installed before 2010, you’re on borrowed time. Even a well-maintained furnace loses efficiency as components wear, and parts availability for older models (especially 80% AFUE units from brands that have changed designs) gets spottier every year.

Rising gas bills without rising comfort

Con Edison rates fluctuate, but if your January bill is 20% higher than last January and your house feels the same or colder, your furnace is burning more gas to produce the same heat. That’s an efficiency leak, and on a 18-year-old furnace, the fix is usually replacement rather than repair.

Repairs within 18 months of each other

Two or more repairs in a two-year span on a furnace over 12 years old is a pattern. The next failure is coming. Yonkers homeowners who replace proactively in spring or fall get better pricing, better scheduling, and no freezing nights without heat.

Yellow flame instead of blue

If you can see the burner flame through the small window on your furnace, it should be a steady blue. Yellow or flickering orange flame means incomplete combustion, which produces carbon monoxide. This is the point where you should shut the furnace off and call a professional immediately. Do not attempt to adjust the burner yourself. Carbon monoxide is colorless, odorless, and deadly, and a yellow flame is its early warning sign.

Cracked heat exchanger

The heat exchanger is the metal chamber that separates combustion gases from the air blowing through your home. Over years of heating and cooling, the metal develops microscopic cracks that widen into actual leaks. A cracked heat exchanger can release carbon monoxide into the living space. Some cracks are visible during inspection; many are only detectable with a combustion analyzer or camera scope. If a technician finds a cracked heat exchanger on a furnace over 12 years old, replacement is the standard recommendation. This is a safety issue, not a comfort issue. Halden Heating and Air Yonkers treats cracked heat exchanger findings as immediate priority calls, and we’ll give you a written replacement quote before anyone touches a tool.

If any of these signs feel familiar, start with a $80-$200 tune-up and inspection. It’s the cheapest way to get a qualified read on your furnace’s remaining life. Call (838) 213-7827 to schedule one.

Furnace Brands and Their Yonkers Replacement Costs

Yonkers homeowners ask us about brands constantly. Here’s the honest breakdown. Halden Heating and Air is certified to service and install Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard, so we don’t have a single brand to push.

• Goodman: $3,800-$5,500 installed. Best value in the industry. 10-year parts warranty. Build quality is fine; it’s the Toyota Corolla of furnaces. Ample parts availability.
• Rheem: $4,000-$5,800 installed. Solid mid-tier. Good heat exchanger design. Quiet operation in newer models.
• Bryant: $4,200-$6,200 installed. Bryant is Carrier’s sister brand, sharing most components at a slightly lower price point.
• Carrier: $4,500-$7,000 installed. The Honda Accord of furnaces. Premium build, excellent parts network, good sound insulation. You pay for the name partly, but it holds resale value.
• Trane: $4,500-$7,200 installed. Rugged and reliable. Trane’s heat exchangers are among the most durable in the industry. Priced at the premium end.
• Lennox: $4,800-$7,400 installed. Top of the efficiency range, and priced accordingly. Lennox’s modulating units are some of the quietest furnaces available.
• York, Daikin, and American Standard: $4,000-$6,500 installed depending on model. All are quality units; Daikin owns Goodman and shares component platforms.

Here’s what matters more than brand: installation quality. A skilled installation of a Goodman furnace will outperform a sloppy installation of a Trane. The installer determines whether the unit is sized correctly (not too big, not too small), whether airflow is balanced, whether the venting is safe and to code, and whether startup settings like gas pressure and blower speed are calibrated properly. Halden Heating and Air does a commissioning check on every replacement we install, verifying temperature rise, gas pressure, and carbon monoxide levels before we leave.

Learn more about our Furnace Replacement in Yonkers process. And if you just need a repair while you decide, our home page has the full picture on what we do.

High-Efficiency vs. Standard Furnaces: What Yonkers Homeowners Should Know

This decision drives most of the price difference between quotes. Here’s the real-world comparison.

Standard efficiency (80% AFUE)

These furnaces convert 80% of the gas they burn into usable heat. The other 20% goes out the chimney as exhaust. They’re vented through a traditional metal flue or chimney, which is why most homes built before 1990 in Yonkers have them. Installation is simpler and cheaper: $3,800-$5,000 for most homes.

The downside: you’re paying for gas that doesn’t heat your home. On a $300 monthly winter gas bill, that’s $60 of waste. Over a 15-year lifespan at current Con Edison rates, that’s $10,000+ in wasted fuel.

High-efficiency (90-97% AFUE)

These condensing furnaces squeeze 90-97% of the energy out of the gas. They use a secondary heat exchanger to capture heat from exhaust gases that would otherwise escape, and they vent through PVC pipe instead of a chimney. Installation costs run $4,500-$7,400 in Yonkers, including the venting conversion most older homes need.

The math works faster in Yonkers than in warmer climates because our heating season runs long. A 96% AFUE furnace on a $300 monthly winter gas bill saves roughly $45-50 per month. Over a six-month heating season, that’s $270-300 per year. On a $1,500 price premium, payback lands around 5-6 years. After that, it’s pure savings.

There’s also the comfort factor. High-efficiency furnaces are quieter, run more evenly, and most are two-stage or modulating, meaning they run at a lower output most of the time (maintaining steady temperature) and only ramp up when the cold demands it. That eliminates the blast-of-heat-then-off cycle that older single-stage furnaces deliver.

If you plan to stay in your Yonkers home for more than 6 years, go high-efficiency. If you’re selling within 3-5 years, a quality 80% unit gets the job done, and some buyers don’t scrutinize the furnace at all. Halden Heating and Air will quote both options with a written price so you can compare side by side.

Yonkers Furnace Replacement: Step-by-Step Process

Here’s exactly how a furnace replacement works when you hire Halden Heating and Air in Yonkers. Most jobs take 1-2 days from start to finish.

1. Call or book online for a free estimate. A real person answers 24/7 at (838) 213-7827. Tell us your address, furnace age, and the symptoms you’ve noticed. We’ll schedule a visit at a time that works for you, and you’ll get a live arrival time you can track to your door.
2. In-home evaluation. Andre Fuller or one of our background-checked technicians arrives in a marked Halden van. We inspect your current furnace, measure your home’s square footage, check ductwork condition, and assess venting requirements. We’ll also look at your gas meter size (Yonkers homes with 200,000+ BTU total gas load sometimes need a larger meter, which Con Edison handles separately).
3. Written quote with options. Before we leave, you get a written price covering at least two furnace options, typically one mid-efficiency and one high-efficiency. The quote includes equipment, labor, permits, venting, removal, and any sheet metal work. No ballpark numbers, no door-step adjustments. The price we write is the price you pay.
4. Scheduling and permitting. Once you approve, we pull the Yonkers mechanical permit and schedule your installation. Summer and early fall replacements usually schedule within 3-7 days. Winter replacements are often next-day for no-heat situations.
5. Removal and installation. Our crew arrives with your new furnace, removes the old unit, and installs the new one. This typically takes 4-8 hours. We handle the old furnace disposal, new plenum fabrication, venting, gas line connections, condensate drainage (for high-efficiency units), and electrical wiring.
6. Commissioning and safety check. Before we leave, we test carbon monoxide levels, verify gas pressure, measure temperature rise (the difference between supply and return air), and dial in blower speed for proper airflow. We run the furnace through a full heating cycle and walk you through the new thermostat.
7. 365-Day Done Right Promise. Every replacement carries our one-year workmanship guarantee. If anything isn’t done right within 365 days of installation, we make it right at no charge. That’s a written guarantee, not a verbal promise.

How to Save on Furnace Replacement in Yonkers

Furnace replacement is a significant purchase, but there are legitimate ways to lower the cost without compromising safety or installation quality.

Replace in the off-season

June through September is the slowest period for furnace work in Yonkers. Contractors have open schedules, and manufacturers sometimes run summer rebates. If your furnace is working but aging, now is the time to replace it. You’ll get better scheduling flexibility and sometimes price advantages. By October, every HVAC company in Westchester is slammed with no-heat emergency calls.

Ask about manufacturer rebates

Carrier, Trane, Lennox, and others run seasonal rebate programs on high-efficiency furnaces, typically $200-$800 depending on the model and time of year. A good contractor should surface these automatically. Halden Heating and Air includes any applicable manufacturer rebates in your written quote, not as an afterthought.

Check Con Edison efficiency incentives

Con Edison and NYSERDA periodically offer rebates and financing for high-efficiency heating equipment in Westchester County. These programs change frequently, but they can be worth $300-$1,000 on qualifying high-efficiency furnaces. We’ll tell you what’s available when we quote.

Don’t buy more furnace than you need

Oversized furnaces are common in Yonkers, often installed decades ago by contractors using rule-of-thumb sizing. A furnace that’s too big short-cycles (turns on and off rapidly), wastes gas, and shortens equipment life. Proper sizing based on Manual J calculation (the industry standard for heating load) sometimes means you can buy a smaller, cheaper furnace than the one being replaced. That’s savings on day one.

Bundle the thermostat and any duct sealing

Smart thermostats are $150-$400 when bought separately, but many contractors discount them $50-$100 when bundled with a replacement. Same goes for basic duct sealing. If you need it anyway, bundling is cheaper than separate service calls.

Get multiple quotes, but compare line items

Get at least two written quotes, ideally three. The key: make sure each quote breaks out equipment, labor, permits, venting, and extras. A $4,200 quote that excludes the permit and venting work is a $4,600 quote in disguise. Halden Heating and Air includes everything in our written estimate so there’s nothing to compare apples-to-oranges about.

Ready to see your number? Call (838) 213-7827 for a free, written furnace replacement estimate in Yonkers.

Why Homeowners Choose Halden Heating and Air for Furnace Replacement

Yonkers has plenty of HVAC companies. Here’s what makes us different, and we’ll put all of it in writing.

Written price before work starts. Every single time. Not an estimate range, not a verbal ballpark. A written line-item price delivered before we touch a tool. If the scope changes mid-job (rare, but old Yonkers homes can surprise), we show you the change with a written update before proceeding. No surprises at the door, ever.

Live arrival times you can track. When you book with Halden Heating and Air, you get a live arrival time on your phone, not a four-hour window. You’ll know who is coming, what they look like, and exactly when they’ll pull up. Book online, get a live arrival time, and track your tech to the door. That’s the Relay Visibility Guarantee, and it’s how we run every job.

365-Day Done Right Promise. Every furnace replacement carries a one-year written workmanship guarantee. If anything about the installation isn’t done right within 365 days, we fix it at no charge. No arguing, no fine print, no “that’s not covered.” This applies to every job we complete.

Free second visit if a repair fails. If we repair your furnace and the same issue recurs within the coverage window, the return visit is free. Automatic. Included. It’s part of the written guarantee, not an add-on.

Live answers, 24/7. When your furnace dies at 2 a.m. in January in Yonkers, you call (838) 213-7827 and a real person picks up. No voicemail tree. No “leave a message and we’ll get back to you during business hours.” Someone is on the line, every hour of every day.

Certified across major brands. We service and install Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That means we recommend what’s right for your home, not whatever we happen to have in the warehouse.

Independently owned, locally operated. Halden Heating and Air was founded in 2004 and operates as an independent business under the Relay Home Co. network. Andre Fuller runs the Yonkers operation with the same standards on every call: written price first, honest recommendations, work done right.

FAQs – Furnace Replacement Cost

How much does furnace replacement cost in Yonkers, NY?

A furnace replacement in Yonkers typically costs between $3,800 and $7,400 for most homes, with the average falling around $4,500 to $6,200. The spread depends on furnace size, efficiency rating, brand, and your home’s venting configuration. Smaller homes (<1,500 sq ft) with straightforward chimney venting land at the low end; larger homes needing high-efficiency units and vent makeovers land at the high end. Call (838) 213-7827 for a free written estimate.

Is it cheaper to repair or replace a furnace?

Furnace repairs in Yonkers cost $150-$700 for most fixes. The replacement decision depends on age and repair frequency: if your furnace is under 10 years old and the repair is under $400, repair typically wins. If the unit is 15+ years old and needs a $500+ repair, replacement is usually the smarter long-term move. Apply the math: age of furnace multiplied by repair cost. If it exceeds $5,000, replace.

Can you replace a furnace in one day?

Yes. Most furnace replacements in Yonkers take 4-8 hours on site for the removal and installation, with the full project (including permitting and inspection) wrapping in 1-2 days. Halden Heating and Air completes the vast majority of standard replacements same-day, and we offer next-day replacement for no-heat emergencies during winter. Call (838) 213-7827 to check current scheduling.

How long does a furnace last in Yonkers?

The average furnace in Yonkers lasts 15-20 years with proper maintenance. Homes that get annual tune-ups ($80-$200) usually hit the upper end of that range. Factors that shorten lifespan include oversized units (which short-cycle), skipped maintenance (dirty burners and blowers strain components), and high humidity in basements causing premature corrosion. If your furnace is over 18 years old, start planning for replacement before it becomes an emergency.

What size furnace do I need for my Yonkers home?

Furnace size depends on square footage, ceiling height, insulation levels, window count, and home orientation, but as a rough guide: 1,000-1,400 sq ft homes typically need 45,000-60,000 BTUs; 1,500-2,000 sq ft need 60,000-80,000 BTUs; 2,000-2,800 sq ft need 80,000-100,000 BTUs; and 3,000+ sq ft need 100,000+ BTUs. A proper Manual J calculation from a technician gives you the exact number. Guessing wrong in either direction wastes money and shortens equipment life.

Do I need a permit to replace a furnace in Yonkers?

Yes. The City of Yonkers requires a mechanical permit for furnace replacement, which includes an inspection of the completed installation. Most contractors handle the permitting as part of the job, and the cost ($150-$450) is typically folded into the written quote. Make sure your quote includes permit costs explicitly. Halden Heating and Air includes all Yonkers permitting and inspection coordination in every replacement quote.

Get Your Free Furnace Replacement Estimate in Yonkers

You now know more about furnace replacement pricing in Yonkers than most homeowners learn until they get burned by a door-step surprise. The next step is simple: get your number.

Call (838) 213-7827 and talk to a real person, any hour of any day. Tell us about your furnace, your home, and your budget. We’ll schedule a free in-home evaluation, give you a written price with multiple options, and if you choose to move forward, you’ll know the cost before any work begins. That’s how we’ve operated since 2004.

Andre Fuller and the Halden Heating and Air Yonkers team are ready when you are. Written price, live arrival time, done right.

Pricing reflects the Yonkers market as of 2026. Halden Heating and Air Yonkers offers free estimates – call (838) 213-7827.

Written by Andre Fuller, Owner at Halden Heating and Air Yonkers, serving Yonkers and Westchester County since 2004.